Knowledge Base

Topics > Questions Regarding Handguards

Questions Regarding Handguards (78 FAQs)

Top 10 FAQs For This Topic

	Will the ARMS #50M-CV S.I.R. SYSTEM for A3 Carbines handguards fit the Bushmaster gas piston rifle? I have tried several aftermarket handguards and the weld at the gas tube does not allow most handguards to be installed.
	How do I remove the handguard from the Varmiter / Predator rifle?
	How do I install a 1 piece Aluminum Handguard?
	I noticed that the Carbon 15 M4 "Flat Top" Carbine uses standard handguards. Would it be possible to use a free float handguard from PRI or DPMS on this upper receiver?
	I don't know what model of rifle and/or gas piston system you used to base your recommendation for the Daniel Defense Omega Rail 7.0 (FAQ #73), but I'm guessing it wasn't your production gas piston 16 " A3 upper. Ordered the DD Omega 7.0 rail and was surprised when it didn't fit. Wasn't even close. Not sure I'm using the correct nomenclature here. but the piston support tube that comes off the gas block is about the same diameter as the barrel and obviuosly won't fit in the top lobe of the handguard. Since I bought my upper very early in the production, my question is this: have you reduced the diameter of the piston support tube from your earlier models that now allows it to fit in the DD rail? I'm having a difficult time finding a rail system that will fit this great rifle. Your FAQ also stated the LWRC and ARMS rails will fit, but given the results of the DD I'm hesitant to order. Any suggestions?
	I have an XM15-E2S. Please advise on everything I need to install a vertical foregrip and part numbers if they are handy. Thanks for your assistance.
	How do I install or remove the B.M.A.S. handguard?
	I have one of your Bushmaster AR15 Dissipators coming. I have a New Set of Triangular Handguards I would like to install. Can you advise how much trouble it is going to be to install the Triangular Handguards? If they can be installed, can you advise just what has to be done?
	Will the ARMS #50M-CV S.I.R System fit over your Gas Piston Retrofit Conversion Kit?
	Installing Varminter Handguards

Recently Added FAQs To This Topic

	I have a M4 carbine. It has the 14.5" barrel, and with the Izzy brake it comes to 16". I want to to put a free float quad rail on it. However, I realized the brake is permanantly mounted onto the barrel. That means I can't get the front sight off of the barrel to be able to put the quad rail on. Is there a way around this problem? I know I could use a two piece quad rail, but I would really like to get a free float on there. Let me know if you have any suggestions to help me out. Thanks.
	I have a Bushmaster Predator rifle and I am trying to remove the factory handguard. I can not get the slip ring to move with a strap wrench or using a heat gun. I do not want to damage it how do I remove it? It has a FF tube handguard. Is there a special wrench?
	I have a Carbon-15 Type 97S pistol. I would like to change the handguard to the one used on your Carbon-15 Law Enforcement Short-Barreled Rifle. (The vented one with 4 picatinny rails). Is that rail available for sale? I see you carry the P-4X rail which looks the same, but does that fit a carbon-15 pistol upper receiver? If so, how much would you charge to install it on my carbon upper receiver? Thanks for your help
	I have a Dissipator and was thinking of putting a quad rail on it. With the different gas block on the dissipator will any rifle length quad rail fit with no modification/s Thanks Doc
	I am interested in the 308 ORC. However I would prefer a Predator type upper. Are there any plans to expand the 308 platform to include more models? Do you offer a free float hand guard for the 308 orc?
	I purchased a Varminter model with the stainless steel barrel and free floating handguards. How do I remove the handguard to allow for a thorough cleaning of the barrel underneath?
	I own a Bushmaster AR15 in CAL 223 with a removable carry handle. I would like to add a Bushmaster V Match Free-Floater Tubular Aluminum Forend. If I remove the front sight do I need to replace it with something else to support the handguard?
	I recently purchased a Bushmaster Modular Carbine. It came with rail covers installed on the 4-rail handguard. There are no instructions on how to properly remove the rail covers. Can you provide proper procedure for removing and reinstalling the rail covers.
	Do you have to use oversized handguards if installing a piston convertion kit. I have a few customers asking that question.
	What tools are needed for removing a vented aluminum forend from your predater hunting rifle for cleaning, and how?